Whirlpool washing machine error codes let the user narrow down what could be the problem with the washing machine.
Whirlpool Washing Machine F0E1 Error – Load In Drum During Drum Cleaning Cycle
Description:
Whirlpool washing machine F0E1 error indicates that there is resistance on the drum during the drum cleaning cycle. If there is washing in the drum, remove it and restart the cycle.
If there is no washing in the drum, check for free rotation of the drum. Inspect the drum for foreign items or small pieces of clothing that could have gotten stuck between the drum and outer tub. Whirlpool washing machine F0E1 error could also be caused by bearings that are failing and causing excessive resistance on the drum.
Action To Take:
- Remove clothes from drum.
- Check for free rotation of drum. Remove any stuck items under the drum.
- Replace bearings if drum is noisy or hard to turn.
Whirlpool Washing Machine F0E2 Error – Over Suds Error
Description:
Whirlpool washing machine F0E2 error is an indication of excessive foaming in the drum. Make sure you are using front loading HE(High Efficiency) detergent. And make sure excessive amount of detergent was not used.
Also Whirlpool F0E2 error can be caused by a machine that has trouble draining. Make sure to check the drain pump filter for blockages. And a problem with the pressure tube/chamber can cause the F0E2 error. Inspect pressure tube for holes.
Action To Take:
- Check that the correct detergent was used.
- Inspect drain pump filter for blockages.
- Check drain pump operation.
- Inspect pressure tube for damage.
Whirlpool Washing Machine F0E3 Error – Over Temperature During Drying Cycle
Description:
Whirlpool washing machine F0E3 indicates that the temperature in the machine has exceeded the desired range during the drying phase of the cycle. This error appears on whirlpool washer/dryer combo machines. Make sure that the machine is not overloaded, overloading can cause poor air circulation and overheating problems.
If machine is not overloaded and error F0E3 is still appearing. Inspect the dryer vent shafts for blockages with lint. Check the operation of dryer fan. Check thermal cut outs and dryer NTC (temperature sensor). NTC sensor resistance should be 16.1K ohm at 86F/30C and 3.4k ohm at 158F/70C.
Action To Take:
- Reduce drying load if overloaded.
- Inspect dryer vents for blockages.
- Check operation of fan, thermal cut outs and NTC sensor.
Whirlpool Washing Machine F0E4 Error – Over Temperature During Washing Cycle
Description:
Whirlpool washing machine F0E4 indicates that the water temperature is hotter than it should be. This could simply be caused by incorrectly connecting the cold water hose to the hot tap.
Also Whirlpool washer F0E4 error can be caused by a stuck heater relay that continuously heats the water non stop or a faulty thermostat.
Action To Take:
- Check that cold inlet hose is connected to cold tap.
- Inspect heater relay for operation.
- Measure resistance of temperature sensor. 16.1K ohm at 86F/30C and 4.9K ohm at 140F/60C.
Whirlpool Washing Machine F0E5 Error – Out of Balance
Description:
Whirlpool washing machine F0E5 error indicates that the washer is going out of balance during the spin cycle. If there is a small load of washing in the machine, this could be the cause of the problem. Small loads do not have enough clothes to distribute around the drum to balance the drum. Also tangled up clothes can cause a F0E5 error on Whirlpool washer. Untangle the clothes and try the cycle again. Because there is a high chance of clothes getting tangled up F0E5 error is one of very common Whirlpool washing machine error codes.
Action To Take:
- Check that the load is not too small.
- Look for any tangled up clothes.
Whirlpool Washing Machine F1E2 Error – MCU Under or Over Voltage Error
Description:
Whirlpool washing machine F1E2 error indicates that the motor control unit is over or under operating voltage. Firstly test that the drum can spin freely.
Then, disconnect the motor plug from the motor control module and measure the resistance between all 3 phases. Resistance between all 3 phases should be between 6-20 ohms. If resistance is with in range, most likely cause of Whirlpool washer F1E2 error will be the motor control unit.
Action To Take:
- Make sure drum is freely rotating.
- Measure motor resistance between all 3 phases.
- Replace motor control unit.
Whirlpool Washing Machine F1E4 Error – Main Relay Open or Shorted Error
Description:
Whirlpool washing machine F1E4 error indicates that there is a problem with the main power relay on the main PCB. Before replacing the main control unit, measure the supply voltage from the RFI filter to main control unit.
Action To Take:
- Measure voltage from RFI to main PCB.
- Replace main PCB.
Whirlpool Washing Machine F3E1 Error – Pressure Sensor Error
Description:
Whirlpool washing machine F3E1 error indicates that the signal from the pressure sensor is out of range or no signal is received at all. Start by checking for bad connections and breaks in the wiring harness.
Then with the multimeter set to DC, measure supply voltage to the the pressure sensor pins 1 and 3. Supply voltage to the pressure sensor should be 5V DC. If supply voltage is normal this will indicate a faulty pressure sensor. If supply voltage is out of range, the main control module will need replacing.
Action To Take:
- Check for loose connector plugs and inspect wiring harness.
- Measure supply voltage to pressure sensor pins 1 & 3. Voltage should be 5V DC.
Whirlpool Washing Machine F3E2 Error – Wash Temperature Sensor Error
Description:
Whirlpool washing machine F3E2 error indicates that the NTC sensor for measuring water temperature is open or short circuit. Firstly check that all the plugs are tightly connected. Then inspect the wiring harness and check the continuity of the NTC sensor harness.
Measure the NTC resistance. 20K ohm at 77F/25C and 4.9K ohm at 140F/60F.
Action To Take:
- Check for loose connector plugs and inspect wiring harness.
- Measure NTC sensor resistance. 20K ohm at 77F/25C and 4.9K ohm at 140F/60F.
Whirlpool Washing Machine F3E3 Error – Dryer Temperature Sensor Error
Description:
Whirlpool washing machine F3E3 error indicates that the NTC sensor for measuring dryer air temperature is open or short circuit. Firstly check that all the plugs are tightly connected. Then inspect the wiring harness and check the continuity of the heater NTC sensor harness.
Measure the NTC resistance. 20K ohm at 77F/25C and 4.9K ohm at 140F/60F.
Action To Take:
- Check for loose connector plugs and inspect wiring harness.
- Measure NTC sensor resistance. 20K ohm at 77F/25C and 4.9K ohm at 140F/60F.
Whirlpool Washing Machine F4E1 Error – Wash Heater Relay Error
Description:
Whirlpool washing machine F4E1 error indicates a fault with the water heater relay. Before replacing the main control board, disconnect the heater plug from the main PCB and measure the heater resistance. The resistance of the heater from the PCB plug should be around 30-34 ohms. If this is the reading you are getting this indicates that the wiring and heater is fine and it is the main PCB at fault. If reading is out of range, measure the resistance directly at the heater, it should be 30-34 ohms, if reading at heater is fine, check the continuity of wiring harness.
Action To Take:
- Check for loose connector plugs and inspect wiring harness.
- Measure water heater resistance. 30-34 ohms, replace heater if out of range.
- Replace main PCB.
